#Docker run image restart driver

t, –tty: It allocates terminal and mostly used with the ‘-i’ option. –rm: It removes the container as soon as container exit or stop running –restart: It allows us to specify restart policy for the container p, –publish: It is used to publish container’s ports to host –network: It is used to connect the container to a different network than the default –name: It is used to specify the name of the container

–mount: It is used to mount filesystem to the container m, –memory: It is used to set memory limit in bytes –log-opts: It is used to specify options to log-driver.

#Docker run image restart driver

–log-driver: It is used to specify the logging driver for the container, it overrides the default log-driver If the option to restart OctopPrint is not present in the user interface, ensure the following command is present in the Restart OctoPrint field under the Server section of the OctoPrint Settings.–link: It adds a link to another container Whilst the container should be pre-configured to allow for OctoPrint to be restarted within the container, there are still some edge cases where this pre-configuration does not take effect. The value of CAMERA_DEV is used in starting the mjpg-streamer service, whereas the devices mapping is used by docker to make sure the container has access to the device.įor example, if you change the CAMERA_DEV to be /dev/video1, you would also need to map /dev/video1:/dev/video1 in your container. Note: You will still need to declare the device mapping in your docker-compose file or docker command, even if you explicitly declare the CAMERA_DEV. recommend you backup before trying this as this is a new feature that has been difficult to test fully Will attempt to detect and migrate filesystems structures from previous versions of this image to be compatible with the latest release version. These are implicit in example docker-compose.yml, and if you wish to change them, refer to the docker-compose docs on setting environment variables. Listed below are the options and their defaults. There are configuration values that you pass using container -environment options. Snapshot: See container environment based configs for a fulllist of webcam configuration options configured with docker.URLs for reaching the camera from outside the container are:

Make sure you use the following internal configuration (Settings » Webcam & Timelapse): If you map a video device other than /dev/video0, you will additionally need to set an environment variable for CAMERA_DEV to match the mapped device mapping. You'll also need to add -device /dev/video0:/dev/video0 to your docker run, or ensure it's listed in the devices array in your docker-compose.yml. This is done by setting the environment variable ENABLE_MJPG_STREAMER=true in your docker run command, or in the docker-compose.yml file.

In order to use the webcam, you'll need to make sure the webcam service is enabled. Configuration Enabling Webcam Support with Docker Open octoprint at See Initial Setup for configuration values to use during your fist launch of OctoPrint using docker. Save the contents of this file on your machine as docker-compose.yml, and then run docker-compose up -d.

We recommend you use docker-compose to run octoprint via docker, and have included a recommended docker-compose.yml file for your convenience. latest|edge|canary|bleeding|X.Y.Z-minimal - a minimal version of each of the tags described above, published under the same condition but from the minimal image.minimal - This is built whenever latest is built, but uses the minimal image.X, X.Y, X.Y.Z, X.Y.Z-rc - these tags will follow the latest build that matches the tag.edge - will always follow the latest release including prereleases.latest - will always follow the latest stable release.Please check out our Roadmap, or join the discussion in the #dev-docker or #support-docker channels on the official OctoPrint Discord .Īll images for the octoprint/octoprint image are multi-arch images, and we publish for arm64, arm/v7, and amd64 using the below tags: In addition, we know that OctoPrint is not the best suited type of application for containerization, but we're working hard to make it as compatible as possible. You can subscribe to be notified of releases as well, by selecting the Watch button in the upper right corner, choosing 'Custom', and checking 'Releases'. As a result we recommend you always check the CHANGELOG or Releases before pulling an image, even if you are pulling the same tag. The octoprint/octoprint image uses semantic versioning, but the tags for octoprint/octoprint follow the version of octoprint contained in the image. It is designed to work similarly, and support the same out of the box features as the octopi raspberry-pi machine image, using docker. This is the primary image of octoprint/octoprint.